Accessories

GOL 4 - 433 MHz Remote Controls

A unique design and innovative materials are featured in these new four channel transmitters.

with fixed, clonable code for use in block of flats; provided with pre-programmed code, which may be changed by means of a key stroke sequence;
Non - Clonable rolling code for safety apply cautions.

Provision for an optional proximity transponder. Availability of a wall mounting and a clip for installation of car sun shades.

433 MHz external aerial.

XEL and Lab - Infrared photocells

These sensors are the most establised solution which ensures the automation system to operate at maximum safety levels.

Modulated infrared beam system. Designed with realiable circuits to ensure highest level of compatability with other accessories and long life.

Lab 3 compact size ensures easier installation even in space restricted applications or when frames and vertical mounting are very narrow or unusually shaped. Designed with elegant and clean lines, this product is suitable for any type of frame, both modern or traditional, residential or industrial.

Lan 7 - Proximity control system with transponder technology

This is an identification system allowing proximity detection of a coded button or card. Consists of one or two Lan 7R units, connected to the Lan 7S control unit, where card or button individual codes are stored.

The receiver/transmitter unit constantly receives/transmits a weak electromagnetic field by means of the built in coil. When the button or the card approach the unit, they absorb electromagnetic energy, which is then retransmitted by means of a signal which also contains the individual code.

The previously stored code activates the automation system control. Both the button and the card are fitted with a non-volatile memory which stores an individual code and therefore do not require internal batteries.

Ideally suited for activating entrance systems fitted to company premises, block of flats or wherever access to authorised personnel is provided.

Cont 1

Card holding base for inside/outside fitting for 1 BIX LR22 or other peripherals.

Lan 4T - Digital keypad

The Lan 4 system is a keyboard based system with a vandal-proof digital combination which, by entering a PIN, allows one or two automation systems or any other device installed up to 300 m away from the decoder to be operated.

The keypads are easy to install either indoor or outdoor. With PIN up to 8 digit long. In case of keyboard tampering and after 25 unsuccessful PIN attempts with 120 s, the keyboard is locked and, for 120 s, it will no longer recognise any PIN, not produce any sound signals. After this time is elapsed, the keyboard will automatically go back to the waiting and PIN entering status.

GOL 4M Control Keypad - New improved product for internal /external use.

433 MHz "rolling code"radio transmitter compatible with current Bix Series radio receivers.

By entering a PIN through the four channel control keyboard, the motorised entrances are opened by radio signals.

Equipped with an internal battery, it does not require mains power and can therefore be easily located anywhere within its operating range.

Can be used to control up to 4 different gates. With PIN number of up to 8 digit long. Incase of keyboard tampering and after 25 unsuccessful PIN entering attempts with 120 s, the keyboard is locked and, for 120 s, it will no longer recognise any PIN, nor produce any sound signals. After this time, the keyboard will automatically go back to the waiting and PIN entering status.

Lab 9 - Magnetic loop detector

Entrance control detector, complete with self calibrating system, automatic sensitivity amplification and a range of operating frequencies to be selected by the user.

This device automatically opens an entrance system by detecting when a vehicle goes over a loop sensor located in the ground.

This device is the ideal control unit for automatic gates/barriers used in car parks, transit ramps and exits in general.

SENSORS

Photocell - Sensors

0CL PR -Sensors

Photocell for door frames to prevent intrapment.

Pas A - Sensors

Active infra-red motion and presence sensor.

RER - Sensors

Passive infra- red motion sensor.

DOOR SELECTORS

COM

COM are the new electronic mechanical and analogue program selectors designed to select and set desired operation modes for one or more automatic doors.

Suitable for sliding and swing doors

The device can be used for sliding or swing doors by simply replacing the frontal keypad, which is usually supplied with the product.

Recognition of the type of automation it is connected to is completely automatic.

COM E

New and elegant

COM E is the new analogue electronic selector designed to set type 94 electronic control panel operation modes, to manage one or more Bis automations. It consists of one unit provided with a micro-monitor, with frontal keyboard and signalling LED.

It is intended for wall fastening, surface or flush mounting, and its size is perfectly compatible with switch and socket square standard.

Operation features

COM E can set up to 4 doors in the same mode
Two COM E can be connected on the same automation
COM EL is also available: it is a complementary, functional and useful accessory for external key lock
TEL RC is an infra-red beam receiving module, which can be housed inside COM E selector, and which, through TEL 2 radio remote control, allows parameter management of the automation to which the selector is connected.

COM H & COM K

These are the new function rotary programme selectors for automatic door operation mode setting. Available in two versions, with actuation by handle (COM H) or by key (COM K), these are both provided with a double interchangeable frontal keypad, for sliding or swing doors. The control instrument is a 6- position rotary electromechanical changeover switch.

These units as well have provision for wall fastening, surface or flush mounting and their size is perfectly compatible with switch and socketsqaure standard.